[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Juniper Config Commit causes Cisco Etherchannels to go into err-disable state

I have cases open with both Cisco and Juniper on this, but wanted to see if
anyone else had seen an issue like this because support has no idea.

I have a Juniper QFX 5100 Core running in Virtual Chassis mode with 4
switches. I have 4 separate stacks of Cisco 3750 switches with 2x1GB
uplinks bound into 4 different LACP trunks. I have had it happen twice now
where I apply a trunk port config(not an LACP trunk) to a port that isn't a
part of any of the LACP trunks and it causes all 4 of the Etherchannels on
the Cisco stacked switches to go into an err-disable state with these
messages:

Mar 14 07:11:33: %PM-4-ERR_DISABLE: channel-misconfig (STP) error detected
on Gi1/0/48, putting Gi1/0/48 in err-disable state

Mar 14 07:11:33: %PM-4-ERR_DISABLE: channel-misconfig (STP) error detected
on Po17, putting Gi1/0/48 in err-disable state

Mar 14 07:11:33: %PM-4-ERR_DISABLE: channel-misconfig (STP) error detected
on Po17, putting Po17 in err-disable state

Mar 14 07:11:34: %LINEPROTO-5-UPDOWN: Line protocol on Interface
GigabitEthernet1/0/48, changed state to down

Mar 14 07:11:33: %PM-4-ERR_DISABLE: channel-misconfig (STP) error detected
on Gi2/0/48, putting Gi2/0/48 in err-disable state (CA-TOR-1-7-2)

Mar 14 07:11:34: %LINEPROTO-5-UPDOWN: Line protocol on Interface
GigabitEthernet2/0/48, changed state to down

Mar 14 07:11:34: %LINEPROTO-5-UPDOWN: Line protocol on Interface
Port-channel17, changed state to down

Here is the config I am applying to the port that has caused this issue to
happen twice now:

set interfaces ge-0/0/67 description "Firewall Port"
set interfaces ge-0/0/67 unit 0 family ethernet-switching interface-mode
trunk
set interfaces ge-0/0/67 unit 0 family ethernet-switching vlan members 9-10
set interfaces ge-0/0/67 unit 0 family ethernet-switching vlan members 29
set interfaces ge-0/0/67 unit 0 family ethernet-switching vlan members 31-32
set interfaces ge-0/0/67 unit 0 family ethernet-switching vlan members 43
set interfaces ge-0/0/67 unit 0 family ethernet-switching vlan members 50-51
set interfaces ge-0/0/67 unit 0 family ethernet-switching vlan members 56
set interfaces ge-0/0/67 unit 0 family ethernet-switching vlan members 58
set interfaces ge-0/0/67 unit 0 family ethernet-switching vlan members 66
set interfaces ge-0/0/67 unit 0 family ethernet-switching vlan members 68
set interfaces ge-0/0/67 unit 0 family ethernet-switching vlan members 90
set interfaces ge-0/0/67 unit 0 family ethernet-switching vlan members 143
set interfaces ge-0/0/67 unit 0 family ethernet-switching vlan members 170

The issue happens within a couple of minutes of committing the config on
the Juniper side, there are no cables plugged into port 0/0/67 so
technically there shouldn't be any BPDU's sent out since there isn't a port
change.

Juniper Support wants me to turn on trace option and then run though a
bunch of scenarios, the issue is that testing this takes down my network.

Just wanted to put it out there to see if anyone else had run into a
situation similar to this.

TIA

Joe