Re: Sizing paper with gum and dichromate

From: Kees Brandenburg ^lt;[email protected]>
Date: 12/20/05-01:06:17 PM Z
Message-id: <1114229.1135105577248.JavaMail.swiki@G3.local>

Joe we're alt-sizing here. While doing these tests I also remembered that I once tried a gum and white gouache first coat. If I remember correctly that was even greener than the ones I saw this week with the unpigmented gum. These last tests are all on unsized BFK. To check all possibilities I also coated a gelatin sized sheed with this uncolored gum and exposed for 30 sec. That one was also stained but more yellow-green than green.

-kees

On Tuesday December 20th 2005, Joe Smigiel wrote:

> Ohhhh, you two are talking about using a layer of exposed dichromated gum sans pigment as a size... Got it now.
> I have a suspicion that adding pigment to the mix helps minimize the green dichromate staining and somehow allows the metabisufite to clear any green chromium stain. Don't know why this is so but it seems to be my general observation and impression rather than being a hard fact based on targeted testing. I intended to test this recently but decided to wait until my chemist colleague got back to me with the results of his study of the green stuff.
> joe
> >>> zphoto@montana.net 12/20/05 11:58 AM >>>
> My experience exactly, Kees, but am excited to see how you feel it does as a
> size ina comparison to gelatin, below. Thanks for testing this--saves me
> mucho time.
> Chris
> ----- Original Message -----
> From: "Kees Brandenburg" <ctb@zeelandnet.nl>
> To: <alt-photo-process-l@sask.usask.ca>
> Sent: Tuesday, December 20, 2005 9:31 AM
> Subject: Re: Sizing paper with gum and dichromate
> Chris,
> I just finished some testing on this subject. I coated several sheets
> of BFK (because I had some leftovers). I mixed my gum (homemade from
> lumps) and dichromate (saturated pot.di) as I allway do in my
> pigmented mix. My usual printing time (UV fluorescent) is 4 minutes.
> I coated 6 sheets and exposed for 4, 2, 1 minute and 30 and 15 sec
> (all through a piece of blank Ultrafine Crystal Clear film). After
> that I left the paper 'develop automaticly' in the water for 1 hour
> (as I allways do) and dried. The next day I cleared (at least tried
> to) the samples in 5% metabisulfite.
> Conclusion: all but one sample had the green stain. The 4,2 and 1
> minute exposed had a severe stain. The one that stayed white was
> exposed for 15 sec. (i.e. 4 stops under normal). The 30 secs sample
> was acceptable allthough stained. Than I coated another one and
> exposed for 30 seconds and left this one in the water overnight. Next
> morning it looked much better than the first 30 sec. sample.
> Next step will be coating these 15 and 30 sec samples with my usual
> pigmented mix and look how they behave compared to gelatine sized paper.
> -kees
> On 20-dec-2005, at 17:06, Christina Z. Anderson wrote:
> > Good morning,
> >
> > I'm late on replying to this post but so it goes at Christmas...
> >
> > My problem with sizing with gum is this: in order to get the layer hard
> > enough to be a suitable size, there will be some discoloration with the
> > dichromate that stays in and discolors the whites, in my practice. So by
> > experience I agree with kees. If I didn't harden to the point of
> > discoloration the layer was too soft. I tried clearing with pot metabi
> > but that whole procedure seemed like so much more work than just biting
> > the bullet and brushing on a hardened gelatin size (e.g. two separate wet
> > and dry cycles). Even so, the layer did not prevent staining.
> >
> > But I would assume somewhere someone out there has luck with this method
> > who is perhaps using lighter pigment loads, although my assumption is
> > also that since this method, quoted in the books long ago, never caught
> > on as primary practice means it just isn't as good as a plain old
> > hardened gelatin size. You know what they say about "assume", though...
> > Chris
> >
> > Probably a much short time will be enough then. But maybe
> > the break even point of hardening enough before the staining starts
> > doesn't even exists.
> > kees
> >
> > Loris Medici wrote:
> >> Hi Kees,
> >> But you will still omit the density of the pigment that way...
> >> Regards,
> >> Loris.
> >> -----Original Message-----
> >> From: Kees Brandenburg [mailto:ctb@zeelandnet.nl] Sent: 15 Aral*k 2005
> >> Per*embe 16:26
> >> To: alt-photo-process-l@sask.usask.ca
> >> Subject: Sizing paper with gum and dichromate, was Re: glut
> >>
> >>
> >> ...But why not standardize things a little bit more and size with gum
> >> and expose with your standard printing time through a clear sheet of
> >> printing substrate (or film). I'll give that a try this week...
> >>
> >>
> >
> >
> >
Received on Tue Dec 20 13:15:05 2005

This archive was generated by hypermail 2.1.8 : 01/05/06-01:45:11 PM Z CST